Duerkopp Adler HP Series Additional guide Manual de usuario descargar pdf (Pagina 82)

EFKA AB220A/320A FP220A/320A

Supplier Level

Code no. 311 with control operation

Code no. 3112 with control panel operation

Parameter Designation Unit max min Preset Ind.

302 tr1 Starting point for signal A1 4 0 0 A/A/A/A

0 = Start at the beginning of the seam

1 = Start of the signal triggered by light barrier sensing

2 = Start of the signal when the drive stops at the seam

end

3 = Start from light barrier covered onwards at the

beginning of the seam

4 = Signal A1 only manually switchable

303 do1 Delay of signal A1 2 0 1 A/A/A/A

0 = No delay until signal On

1 = Delay over time until signal On

2 = Delay over stitches until signal On

304 dt1 Delay time until signal A1 On ms 2550 **) 0 0 A/A/A/A

305 St1 ON period of signal A1 ms 2550 **) 0 0 A/A/A/A

306 nA1 Speed mode when signal A1 is On 2 0 0 A/A/A/A

0 = Pedal controlled speed

1 = Limited speed n9

2 = Limited speed n11

307 A1 Signal A1 On/Off 1 0 0 A/A/A/A

308 dA1 Stitches delaying signal A1 stitches 999 0 0 A/A/A/A

309 cA1 Stitch counting during signal A1 stitches 999 0 0 A/A/A/A

310 AA2 Selectable power transistors for signal A2 12 0 0 A/A/A/A

0 = No function

1 = Signal on output M1

2 = Signal on output M2

3 = Signal on output M3

4 = Signal on output M4

5 = Signal on output M5

6 = Signal on output M6

7 = Signal on output M7

8 = Signal on output M8

9 = Signal on output M9

10 = Signal on output M10

11 = Signal on output M11

12 = Signal on output VR

311 So2 Issue signal A2 4 0 0 F/F/F/E

0 = Signal until seam end (according to setting of

parameter 320)

1 = Signal over time

2 = Signal until seam end and drive stops

3 = Signal during stitch counting (according to setting

of parameter 319)

4 = Signal A2 as puller function

312 tr2 Starting point for signal A2 4 0 0 A/A/A/A

0 = Start at the beginning of the seam

1 = Start of the signal triggered by light barrier sensing

2 = Start of the signal when the drive stops at the seam

end

3 = Start from light barrier covered onwards at the

beginning of the seam

4 = Signal A2 only manually switchable

313 do2 Delay of signal A2 2 0 1 A/A/A/A

0 = No delay until signal On

1 = Delay over time until signal On

2 = Delay over stitches until signal On

314 dt2 Delay time until signal A2 On ms 2550 **) 0 0 A/A/A/A

315 St2 ON period of signal A2 ms 2550 **) 0 0 A/A/A/A

*) Depending on the selected mode. See table at the beginning of the List of Parameters!

**) When programming the 3-digit or 4-digit control parameter values (without control panel), the 2-digit or 3-digit

value displayed must be multiplied by 10.

1 2 ... 77 78 79 80 81 82 83 84 85 86 87 88

Comentarios a estos manuales

Sin comentarios

Duerkopp Adler HP Series Additional guide Manual de usuario Pagina 82

Comentarios a estos manuales

Relacionado con productos y manuales para Máquinas De Coser Duerkopp Adler HP Series Additional guide