Duerkopp Adler HP Series Additional guide Manual de usuario descargar pdf (Pagina 76)

EFKA AB220A/320A FP220A/320A

76

Supplier Level

Code no. 311 with control operation

Code no. 3112 with control panel operation

Parameter Designation Unit max min Preset Ind.

243 in4 Selection of input function on socket ST2/8 66 0 0 *) F/F/F/E

for input 4

0 = No function

All other functions of the keys as with parameter 240

244 in5 Selection of input function on socket ST2/5 66 0 0 *) F/F/F/E

for input 5

0 = No function

All other functions of the keys as with parameter 240

245 in6 Selection of input function on socket ST2/12 66 0 0 *) F/F/F/E

for input 6

0 = No function

All other functions of the keys as with parameter 240

246 in7 Selection of input function on socket ST2/9 66 0 0 *) F/F/F/E

for input 7

0 = No function

All other functions of the keys as with parameter 240

247 in8 Selection of input function on socket ST2/10 66 0 0 *) F/F/F/E

for input 8

0 = No function

All other functions of the keys as with parameter 240

248 in9 Selection of input function on socket ST2/13 66 0 0 *) F/F/F/E

for input 9

0 = No function

All other functions of the keys as with parameter 240

249 i10 Selection of input function on socket ST2/14 66 0 0 *) F/F/F/E

for input 10

0 = No function

All other functions of the keys as with parameter 240

250 iFA Thread trimmer activation angle degrees 359 0 180 *) A/A/A/A

251 FSA Switch-off delay of thread tension release ms 990 0 50 *) A/A/A/A

252 FSE Switch-on delay angle of thread tension release degrees 359 0 0 *) A/A/A/A

253 tFA Stop time for thread trimmer ms 500 **) 0 70 *) A/A/A/A

254 EF- Upper limit (pa. 204) duty ratio for sewing % 100 1 100 *) A/A/A/A

foot lift 1...100

255 EV- Upper limit (pa. 213) duty ratio for backtacking/ % 100 1 100 *) A/A/A/A

thread trimmer backward 1...100

256 kt6 Delay time of output VR (chain suction), ms 2550 **) 0 250 A/A/A/A

(function only if parameter 290 = 15)

257 c7 Start counting until tape cutter M4 On stitches 254 0 5 A/A/A/A

(function only if parameter 290 = 15)

258 c8 End counting until tape cutter M4 On stitches 254 0 15 A/A/A/A

(function only if parameter 290 = 15)

259 FAE Switch-on delay angle of the thread trimmer degrees 359 0 0 *) C/C/C/B

260 ihr Handwheel increments carried out when the incr. 500 0 10 *) A/A/A/A

key is pressed once (in1...i10)

261 nhr Handwheel speed RPM 150 **) 30 50 A/A/A/A

262 dhr Delay time until the key is pressed down ms 2550 **) 0 200 *) A/A/A/A

causing the handwheel to rotate continuously

(in1...i10).

Pressing the key briefly < preset value of

parameter 262: increments set by means of

parameter 260 are carried out.

Keeping the key pressed down > preset value

of parameter 262: handwheel rotates

continuously.

*) Depending on the selected mode. See table at the beginning of the List of Parameters!

**) When programming the 3-digit or 4-digit control parameter values (without control panel), the 2-digit or 3-digit

value displayed must be multiplied by 10.

1 2 ... 71 72 73 74 75 76 77 78 79 80 81 ... 87 88

Comentarios a estos manuales

Sin comentarios