Duerkopp Adler HP Series Additional guide Manual de usuario descargar pdf (Pagina 73)

EFKA AB220A/320A FP220A/320A

9.4 Supplier Level

Code no. 311 with control operation

Code no. 3112 with control panel operation

Parameter Designation Unit max min Preset Ind.

200 t1 Delay until speed release after start backtack ms 500 0 100 *) A/A/A/A

201 t2 Sewing foot lift switch-on delay with half ms 500 20 80 *) A/A/A/A

heelback

202 t3 Start delay after disabling the sewing foot ms 500 0 50 *) A/A/A/A

lift signal

203 t4 Time of full power of sewing foot lifting ms 600 0 500 *) A/A/A/A

204 t5 Holding power for sewing foot lifting % pa. 254 1 40 *) A/A/A/A

1...100%

1% è low holding power

100% è high holding power

205 t6 Thread wiper time ms 2550 **) 0 120 *) A/A/A/A

206 t7 Delay from end of thread wiper until sewing ms 800 0 40 *) A/A/A/A

foot lifting On

207 br1 Braking effect when modifying the preset value

≤ 4 stages

(indicated values only with transmission ratio 1:1)

Values with the AB220A.... / FP220A.... controls 55 1 15 A/A/A/A

Values with the AB320A.... / FP320A.... controls 55 1 20 A/A/A/A

208 br2 Braking effect when modifying the preset value

≥ 5 stages

(indicated values only with transmission ratio 1:1)

Values with the AB220A.... / FP220A.... controls 55 1 35 A/A/A/A

Values with the AB320A.... / FP320A.... controls 55 1 30 A/A/A/A

209 dFw Thread wiper start delay ms 2550 **) 0 0 *) A/A/A/A

210 tSr Stop time for switching the stitch regulator ms 500 0 140 A/A/A/A

in the ornamental backtack

211 tFL Sewing foot lift switch-on delay with thread ms 500 0 60 *) A/A/A/A

wiper off

212 t10 Time of full power of backtacking or thread ms 600 0 500 A/A/A/A

trimmer forward

213 t11 Holding power for backtacking or thread % pa. 255 1 40 *) A/A/A/A

trimmer backward 1...100%

1% è low holding power

100% è high holding power

214 rAt No function 160 040 080 F/F/F/E

219 br3 Braking power at stop of the drive

Values with the AB220A.... / FP220A.... controls 55 1 10 A/A/A/A

Values with the AB320A.... / FP320A.... controls 55 1 10 A/A/A/A

220 ALF Accelerating power of the drive

(indicated values only with transmission ratio 1:1)

Values with the AB220A.... / FP220A.... controls 55 1 35 A/A/A/A

Values with the AB320A.... / FP320A.... controls 55 1 20 A/A/A/A

221 dGn Speed gate 1 RPM 990 **) 50 100 A/A/A/A

222 tGn Speed gate damping period ms 990 0 20 F/F/F/E

(effective only if parameter 224 = 0)

223 dG2 Speed gate 2 RPM 4500 **) 200 1600 F/F/F/E

224 dGF Speed gate 2 On/Off 1 0 1 A/A/A/A

225 br4 Setting the braking curve for the light barrier and

machine run blockage (values only with transmission

ratio 1:1)

Values with the AB220A.... / FP220A.... controls 55 1 55 A/A/A/A

Values with the AB320A.... / FP320A.... controls 55 1 55 A/A/A/A

231 Sn1 Execution of the first stitch after Power On at 1 0 0 *) A/A/A/A

positioning speed

232 USS Overlock with fast scissors On/Off 1 0 0 A/A/A/A

0 = Tape cutter

1 = Fast scissors (set parameter 282 = 0)

*) Depending on the selected mode. See table at the beginning of the List of Parameters!

**) When programming the 3-digit or 4-digit control parameter values (without control panel), the 2-digit or 3-digit

value displayed must be multiplied by 10.

1 2 ... 68 69 70 71 72 73 74 75 76 77 78 ... 87 88

Comentarios a estos manuales

Sin comentarios

Duerkopp Adler HP Series Additional guide Manual de usuario Pagina 73

Comentarios a estos manuales

Relacionado con productos y manuales para Máquinas De Coser Duerkopp Adler HP Series Additional guide