Duerkopp Adler HP Series Additional guide Manual de instrucciones Pagina 68
- Pagina / 84
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
EFKA AB220A5111
68
Supplier Level
Code no. 311 with control operation
Code no. 3112 with control panel operation
Parameter Designation Unit max min Preset Ind.
237 tkS Switch-off delay for chain suction at the ms 2550 **) 0 0 A
seam end, if parameter 022 = 2.
238 EnP Software debouncing for all inputs: 1 0 1 A
0 = No debouncing
1 = With debouncing
239 FEL Selection of the input function on socket B18/5 47 0 0 A
0 = Light barrier function, if 009 = 1
All other functions as with parameter 240.
240 in1 Selection of the input functions on socket ST2/7 47 0 0 *) A
for input 1
0 = No function
1 = Needle up/down
2 = Needle up
3 = Single stitch (basting stitch)
4 = Full stitch
5 = Needle to position 2
6 = Machine run blockage effective with open
contact
7 = Machine run blockage effective with closed
contact
8 = Machine run blockage unpositioned effective
with open contact
9 = Machine run blockage unpositioned effective
with closed contact
10 = Automatic speed n12 without pedal
11 = Limited speed n12 pedal controlled
(see parameter 266)
12 = Sewing foot lifting with pedal in position 0
(neutral)
13 = High lift for walking foot with speed limitation n10
(operational mode not stored)
14 = High lift for walking foot (flip-flop 1) with speed
limitation n10
15 = Tape cutter / fast scissors: function only in
chainstitch and overlock mode
16 = Intermediate backtack / intermediate stitch
condensing
17 = Stitch regulator suppression / recall
18 = Unlocking the chain: can be activated by
keystroke, but will be executed only at the
seam end
19 = Reset bobbin thread monitor if parameter
030 = >0
20 = Handwheel running in the direction of rotation
according to the setting of parameter 161
21 = Handwheel running in the opposite direction of
rotation according to the setting of parameter
161
22 = Speed limitation n11 (flip-flop 2). Output
ST2/29 is enabled according to setting of
parameter 186
23 = No function
24 = No function
25 = Speed limitation with ext. potentiometer
On/Off (see parameter 126)
26 = Manual stacker
27 = Unlocking the chain, function is performed
upon pressing the key
28 = External light barrier (according to the
setting of parameter 131)
*) Depending on the selected mode. See table at the beginning of the List of Parameters!
**) When programming the 3-digit or 4-digit control parameter values (without control panel), the 2-digit or 3-digit
value displayed must be multiplied by 10.
- CONTROL AB220A5111 1
- LIST OF PARAMETERS 1
- EFKA AB220A51113 3
- CONTENTS Page 3
- 1 Table of Adapter Cords 5
- 2 Putting into Service 6
- Routine (SIR) 7
- EFKA AB220A51119 9
- EFKA AB220A5111 10
- 4.3 Connection Diagram 10
- EFKA AB220A511111 11
- ATTENTION! 12
- EFKA AB220A511113 13
- EFKA AB220A511115 15
- 5.1 Adapter Cords 15
- Nr. 1112822 16
- EFKA AB220A511117 17
- EFKA AB220A511119 19
- Nr. 1113200 19
- EFKA AB220A511121 21
- EFKA AB220A511123 23
- Nr.1113267 23
- EFKA AB220A511125 25
- Nr. 1112823 25
- EFKA AB220A511127 27
- Nr. 1113178 28
- EFKA AB220A511129 29
- 6 Timing Diagrams 30
- EFKA AB220A511131 31
- EFKA AB220A511133 33
- EFKA AB220A511135 35
- EFKA AB220A511137 37
- EFKA AB220A511139 39
- EFKA AB220A511141 41
- EFKA AB220A511143 43
- EFKA AB220A511145 45
- EFKA AB220A511147 47
- EFKA AB220A511149 49
- EFKA AB220A511151 51
- EFKA AB220A511153 53
- EFKA AB220A511155 55
- 7 List of Parameters 57
- Supplier Level 58
- EFKA AB220A511159 59
- 7.2 Operator Level 59
- Operator Level 60
- EFKA AB220A511161 61
- 7.3 Technician Level 61
- Technician Level 62
- EFKA AB220A511163 63
- EFKA AB220A511165 65
- EFKA AB220A511167 67
- 7.4 Supplier Level 67
- EFKA AB220A511169 69
- EFKA AB220A511171 71
- EFKA AB220A511173 73
- EFKA AB220A511175 75
- EFKA AB220A511177 77
- EFKA AB220A511179 79
- 8 Error Displays 80
- EFKA AB220A511183 83
- OF AMERICA INC 84
Relacionado con productos y manuales para Máquinas De Coser Duerkopp Adler HP Series Additional guide
(6 paginas)
Máquinas De Coser Duerkopp Adler 806 Manual de servicio
(114 paginas)
(114 paginas)
(88 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales